Se você está com dificuldade em logar, esqueceu seu usuário e senha, por favor entre em contato conosco mandando uma mensagem em nossa página do facebook: Fórum Paintball Cenário que iremos lhe auxiliar.
Tamanhos de O´rings Tippmann
Tamanhos de O´rings Tippmann
Achei isso no fórum da Tippmann:
Pro-Lite
Barrel pinch bolt - 1/4-20 thd, 5/8" length
Elbow pinch bolt - 1/4-20 thd, 1" length
Gripframe mount bolts - 10-32 thd, 3/8" length
Gripframe half bolt (top) - 10-32 thd, 7/8" length
Gripframe half bolt (bottom) - 10-32 thd, 1 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/4" length set screw
Gripframe mount sleeves - 10-32 thd internal, 5/8" length, 1/4" diameter
Pro-Carbine (Many of these are applicable to 68-Carbine as well)
Barrel pinch bolt - 1/4-20 thd, 5/8" length
Elbow pinch bolt - 1/4-20 thd, 1" length
Gripframe mount bolts - 10-32 thd, 3/8" length
Grip panel bolts - 6-32 thd, 3/8" length
Bottomline mount bolts - 10-32 thd, 1" length
Velocity adjustment bolt - 1/4-20 thd, 7/8" length
98 Custom
Elbow pinch bolt - 1/4-20 thd, 1" length
Elbow latch bolts (Holding the part that catches the front sight) - 6-32 thd, 1/4" length
Main half bolts - 10-32 thd, 5/8" length
Foregrip half bolt - 10-32 thd, 1 1/8" length
Grip panel bolts - 6-32 thd, 3/8" length
Bottomline mount bolts - 10-32 thd, 1" length
Valve bolts - 10-32 thd, 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/8" length set screw
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Inside valve O-Rings (2x): -12 size
C-3
All major half bolts - 10-32 thd, 5/8" length
Front sight pinch bolt - 10-32 thd, 1" length
Grip panel bolts - 6-32 thd, 3/8" length
Regulator bolts - 10-32 thd, 1" length
Bottomline bolts - 10-32 thd, 1" length
Extra notes:
C-3 Rear sight piece, stock grip panels, and trigger guard are identical to these 98 Custom parts. The C-3 also has a single push pin identical to that of an A-5 for the reciever to pump guide rod mount.
Also the gas transfer tubing on the right side of the reciever uses Clippard part number UT0-2 swivel fittings.
X-7
Main half bolts: 4x 10-32 thd, 5/8" length, 2x 10-32 thd, 7/8" length
Cyclone mounting bolt: 1/4-20 thd, 7/8" length
Bottomline bolt: 10-32 thd, 1 1/8" length
Foregrip side rail bolts: 6-32 thd, 1/4" length
Front sight bolt: 10-32 thd, 7/8" length
Rear sight bolts: 10-32 thd, 1" length
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Inside valve O-Ring (Behind the valve seat): -12 size
Valve tombstone O-Ring: -111 size
End cap O-Ring: -117 size
Extra notes: Uses push-pins the same as the A-5.
Trigger guard is the same as the A-5.
98 Custom Platinum
Elbow pinch bolt - 1/4-20 thd, 1" length
Elbow latch bolts (Holding the part that catches the front sight) - 6-32 thd, 1/4" length
Main half bolts - 6x 10-32 thd, 5/8" length
Foregrip half bolt - 10-32 thd, 1 1/8" length
Grip screws - 4x 6-32 thd, 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/8" length set screw
Weaver rail bolts - 3x 6-32 thd, 3/8" length
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Valve internal O-Rings: 2x -12 size
Large O-Ring set into the right gun half, seals the cyclone/RT air tap: -116 size
Extra notes: Uses no valve bolts like the original 98.
The gas line to the valve is a special fitting, using a left-hand threaded square nut inside the gun halves. Doubtful you could find this at a hardware store.
TPX Pistol
Half bolts: All 10-32 threaded, 4x 5/8 length, 2x 1/2 length, 1x 1 inch length.
Trigger valve bolts: 2x 6-32 threaded, 1/4 length
Bolt buffer o-ring: -118 size
Main valve end cap, large o-ring: -19 size
Main valve end cap, small o-ring: -12 size
Main valve core, large o-ring: -12 size
Main valve core, small o-rings: -10 size
Trigger valve internal o-ring: -3 size
Puncture valve internal o-ring: -12 size
Bolt tip o-ring: -15 size
Inside breech o-ring: -19 size
Other
The RT kits and the A-5 Cyclone air fittings are stock parts from Clippard.
Swivel fittings: Clippard part number UT0-2
Flow control for RT: Clippard part number MFC-3AK1
Hose: Clippard part number URH1-0402-BKS-050 (Commonly called Cocker LP hose, works for that too. 50 feet is the smallest amount you can buy direct, so check local shops first.)
Tank O-Rings are the same size as Tippmann front bolt O-Rings, -15 size.
http://www.tippmann.com/forum/wwf77a/fo ... TID=150225
Abs
Pro-Lite
Barrel pinch bolt - 1/4-20 thd, 5/8" length
Elbow pinch bolt - 1/4-20 thd, 1" length
Gripframe mount bolts - 10-32 thd, 3/8" length
Gripframe half bolt (top) - 10-32 thd, 7/8" length
Gripframe half bolt (bottom) - 10-32 thd, 1 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/4" length set screw
Gripframe mount sleeves - 10-32 thd internal, 5/8" length, 1/4" diameter
Pro-Carbine (Many of these are applicable to 68-Carbine as well)
Barrel pinch bolt - 1/4-20 thd, 5/8" length
Elbow pinch bolt - 1/4-20 thd, 1" length
Gripframe mount bolts - 10-32 thd, 3/8" length
Grip panel bolts - 6-32 thd, 3/8" length
Bottomline mount bolts - 10-32 thd, 1" length
Velocity adjustment bolt - 1/4-20 thd, 7/8" length
98 Custom
Elbow pinch bolt - 1/4-20 thd, 1" length
Elbow latch bolts (Holding the part that catches the front sight) - 6-32 thd, 1/4" length
Main half bolts - 10-32 thd, 5/8" length
Foregrip half bolt - 10-32 thd, 1 1/8" length
Grip panel bolts - 6-32 thd, 3/8" length
Bottomline mount bolts - 10-32 thd, 1" length
Valve bolts - 10-32 thd, 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/8" length set screw
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Inside valve O-Rings (2x): -12 size
C-3
All major half bolts - 10-32 thd, 5/8" length
Front sight pinch bolt - 10-32 thd, 1" length
Grip panel bolts - 6-32 thd, 3/8" length
Regulator bolts - 10-32 thd, 1" length
Bottomline bolts - 10-32 thd, 1" length
Extra notes:
C-3 Rear sight piece, stock grip panels, and trigger guard are identical to these 98 Custom parts. The C-3 also has a single push pin identical to that of an A-5 for the reciever to pump guide rod mount.
Also the gas transfer tubing on the right side of the reciever uses Clippard part number UT0-2 swivel fittings.
X-7
Main half bolts: 4x 10-32 thd, 5/8" length, 2x 10-32 thd, 7/8" length
Cyclone mounting bolt: 1/4-20 thd, 7/8" length
Bottomline bolt: 10-32 thd, 1 1/8" length
Foregrip side rail bolts: 6-32 thd, 1/4" length
Front sight bolt: 10-32 thd, 7/8" length
Rear sight bolts: 10-32 thd, 1" length
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Inside valve O-Ring (Behind the valve seat): -12 size
Valve tombstone O-Ring: -111 size
End cap O-Ring: -117 size
Extra notes: Uses push-pins the same as the A-5.
Trigger guard is the same as the A-5.
98 Custom Platinum
Elbow pinch bolt - 1/4-20 thd, 1" length
Elbow latch bolts (Holding the part that catches the front sight) - 6-32 thd, 1/4" length
Main half bolts - 6x 10-32 thd, 5/8" length
Foregrip half bolt - 10-32 thd, 1 1/8" length
Grip screws - 4x 6-32 thd, 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/8" length set screw
Weaver rail bolts - 3x 6-32 thd, 3/8" length
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Valve internal O-Rings: 2x -12 size
Large O-Ring set into the right gun half, seals the cyclone/RT air tap: -116 size
Extra notes: Uses no valve bolts like the original 98.
The gas line to the valve is a special fitting, using a left-hand threaded square nut inside the gun halves. Doubtful you could find this at a hardware store.
TPX Pistol
Half bolts: All 10-32 threaded, 4x 5/8 length, 2x 1/2 length, 1x 1 inch length.
Trigger valve bolts: 2x 6-32 threaded, 1/4 length
Bolt buffer o-ring: -118 size
Main valve end cap, large o-ring: -19 size
Main valve end cap, small o-ring: -12 size
Main valve core, large o-ring: -12 size
Main valve core, small o-rings: -10 size
Trigger valve internal o-ring: -3 size
Puncture valve internal o-ring: -12 size
Bolt tip o-ring: -15 size
Inside breech o-ring: -19 size
Other
The RT kits and the A-5 Cyclone air fittings are stock parts from Clippard.
Swivel fittings: Clippard part number UT0-2
Flow control for RT: Clippard part number MFC-3AK1
Hose: Clippard part number URH1-0402-BKS-050 (Commonly called Cocker LP hose, works for that too. 50 feet is the smallest amount you can buy direct, so check local shops first.)
Tank O-Rings are the same size as Tippmann front bolt O-Rings, -15 size.
http://www.tippmann.com/forum/wwf77a/fo ... TID=150225
Abs
- Roger
- Administrador
- Mensagens: 7770
- Registrado em: 16 Abr 2007, 22:53
- Federado: FPESP #2
- Localização: SP
- Contato:
Re: Tamanhos de O´rings Tippmann
Cara você não imagina o quanto eu procurei isto para finalizar o projeto da minha L96. Só faltava os orings que eu não achava em lugar nenhum.
Boa!!
Vai para o prego!
Boa!!
Vai para o prego!
Re: Tamanhos de O´rings Tippmann
Aproveitando o tópico: meu remote (um Ninja com slide check) esta precisando de ring. Sou do rio. Somente acho rings com medidas métricas, e o ring tem um tamamnho intermediário a estas medidas.
Alguém poderia me orientar onde adquirir?
Grato!
Alguém poderia me orientar onde adquirir?
Grato!
Re: Tamanhos de O´rings Tippmann
Munido dessas medidas é so eu chegar e apresentar a lista na loja de hidrualica/pneumatica que vao saber exatamente oq me dar?
98 Custom
Elbow pinch bolt - 1/4-20 thd, 1" length
Elbow latch bolts (Holding the part that catches the front sight) - 6-32 thd, 1/4" length
Main half bolts - 10-32 thd, 5/8" length
Foregrip half bolt - 10-32 thd, 1 1/8" length
Grip panel bolts - 6-32 thd, 3/8" length
Bottomline mount bolts - 10-32 thd, 1" length
Valve bolts - 10-32 thd, 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/8" length set screw
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Inside valve O-Rings (2x): -12 size
98 Custom
Elbow pinch bolt - 1/4-20 thd, 1" length
Elbow latch bolts (Holding the part that catches the front sight) - 6-32 thd, 1/4" length
Main half bolts - 10-32 thd, 5/8" length
Foregrip half bolt - 10-32 thd, 1 1/8" length
Grip panel bolts - 6-32 thd, 3/8" length
Bottomline mount bolts - 10-32 thd, 1" length
Valve bolts - 10-32 thd, 1/4" length
Velocity adjustment bolt - 1/4-28 thd, 3/8" length set screw
Rear bolt O-Ring: -19 size
Front bolt O-Ring: -15 size
Valve body O-Ring: -19 size
Inside valve O-Rings (2x): -12 size
Re: Tamanhos de O´rings Tippmann
Gunther escreveu:Aproveitando o tópico: meu remote (um Ninja com slide check) esta precisando de ring. Sou do rio. Somente acho rings com medidas métricas, e o ring tem um tamamnho intermediário a estas medidas.
Alguém poderia me orientar onde adquirir?
Grato!
Vai na Rubber Tec em sao cristovao, fica na rua bela.
Leva o oring que eles tem com certeza
-
- private
- Mensagens: 11
- Registrado em: 13 Jun 2010, 16:15
Re: Tamanhos de O´rings Tippmann
Alguem ai sabe onde eu acho o'rings de t98?
VLW
VLW
Re: Tamanhos de O´rings Tippmann
Estou com uma duvida enorme!
Estava testando minha phenom e ao termino desmontei toda ela, e pude ver que ficou uma bolinha dentro dela, ai sem o cano eu engatei o remote e dei um disparo para retirar a bolinha. no chão havia um ring caído,
Duvida esse ring pode ter caído do meu marcador devido eu não ter colocado o cano éter efetuado o disparo?
Me ajudem por favor. a duvida existe por eu esta em um paintball e não sei se foi do meu marcador ou de outra pessoa. Muito obrigado!!!!
Estava testando minha phenom e ao termino desmontei toda ela, e pude ver que ficou uma bolinha dentro dela, ai sem o cano eu engatei o remote e dei um disparo para retirar a bolinha. no chão havia um ring caído,
Duvida esse ring pode ter caído do meu marcador devido eu não ter colocado o cano éter efetuado o disparo?
Me ajudem por favor. a duvida existe por eu esta em um paintball e não sei se foi do meu marcador ou de outra pessoa. Muito obrigado!!!!
Re: Tamanhos de O´rings Tippmann
Os o'rings da alpha black são iguais os da 98 custom , platinum ou não tem nada a ver com nenhuma das duas??
Re: Tamanhos de O´rings Tippmann
e o da a5 vc sabe?
Re: Tamanhos de O´rings Tippmann
Ufa... eu estava procurando exatamente isso... rsss
- eduardoandrad6
- lance corporal
- Mensagens: 116
- Registrado em: 21 Mai 2011, 10:59
Re: Tamanhos de O´rings Tippmann
Alguem poderia me enformar o tamanho dos oring's da TM-15 e da Rap4 t68????
Re: Tamanhos de O´rings Tippmann
Valew cara tava precisando destas especificações!!!
- rpontess
- private
- Mensagens: 54
- Registrado em: 24 Set 2011, 16:50
- Localização: Florianópolis / SC
- Contato:
Re: Tamanhos de O´rings Tippmann
Comprei Orings para minha A5 no Ebay, é só escolher se vai comprar da China ou EUA, e o preço é sempre melhor que no Brasil.
Abs,
Abs,
- SELVA-TERROR
- sergeant
- Mensagens: 330
- Registrado em: 19 Jul 2010, 06:29
- Localização: São Carlos - SP
Re: Tamanhos de O´rings Tippmann
Agora sim posso comprar todos os orings da minha 98
- humgeo2016
- Recruit
- Mensagens: 4
- Registrado em: 16 Mar 2016, 20:16
- Localização: JUAZEIRO DO NORTE-CE
Re: Tamanhos de O´rings Tippmann
Adquiri meu primeiro marcador, um Tippmann 98 custom, e estou com uma baita dúvida. Ao mesmo tempo que adquiri o marcador, comprei também um cano de 14" como primeiro upgrade. O problema é que percebi que o mesmo veio sem o O-ring, diferentemente do original. Minha dúvida é:
- É possível jogar com cano sem o-ring, pode causar algum dano ao marcador ou a jogabilidade?
Vejam na imagem comparativa entre os dois canos...
- É possível jogar com cano sem o-ring, pode causar algum dano ao marcador ou a jogabilidade?
Vejam na imagem comparativa entre os dois canos...